Rogue Engineer

Difficulty

Hours

Cancel
  • You need to swap the shelf #1 and #2 dimensions in the attached drawing. 83-1/4" and 41-1/4" dimensions are wrong. Have a look :)
    Thanks for this nice plan!
    By MecAutAUS, on January 15, 2019

View All Comments
Cancel
  • is the trim between units 3/4" as well? what would you recommend sealing the inside of the plywood drawer boxes with?
    By Blanca8791, on March 17, 2019

  • Great job. Great imagination 
    By Trizmegistus, on May 19, 2019

  • This is exactly the sort of design I've been looking for Thank you!

    By cnoher0, on May 20, 2019
View All Comments
Cancel
  • Where did you purchase the slides for this project?
    By shop4camp, on February 14, 2018
    • You can find bench seat rails at a home improvement store, such as The Home Depot.
      By RYOBI NATION, on February 14, 2018
View All Comments
Cancel
  • Those dolls are going to get a nice nap in their new bed!
    By RYOBI Nation, on September 6, 2017

  • Where is the PDF for the bunk beds
    By Bigkypoppa, on September 6, 2017

  • The link is in the description. Right above the video.
    By Rogue Engineer, on September 6, 2017

  • I may have missed it but is there a measurement for the corner cut outs on the 10"x 20.5" sections?  I'm assuming about 1/2 inch?
    By Dan_Gray, on October 27, 2018
View All Comments
Cancel
  • This was a great project! My 2-year-old absolutely loves the finished piece and I had a lot of fun building it. For anyone else thinking about doing it, I highly recommend it, but here are some things I learned: 

    1- I bought very inexpensive whiteboard from Home Depot. It's fine, but if I could do it again I would likely buy something a little nicer.

    2- The link to buy the tubs wasn't working, but I found them at Target. I imagine different tubs would work, but only if you adjust your measurements on the actual table. These plans are very accurate and if you get the exact tubs, it will all fit perfectly. 

    3- I definitely recommend water-sealing the table if you don't use Cedar. Our table got thoroughly wet after only a few minutes of play time. 
    By mattrweir, on April 28, 2020

  • Great idea~
    By A2fam4, on August 18, 2020
View All Comments
Cancel
  • What are the bearings? Where did you get them?
    By jasonhash, on May 31, 2017
    • They are ceramic skate bearing and I got them off Amazon.
      By Rogue Engineer, on May 31, 2017

  • These sure are in high demand! Your kids must be thrilled you can make them right at home. Nice work!
    By RYOBI Nation, on May 31, 2017

View All Comments
Cancel
  • What water balloon launcher did you use for this?
    By biglosman, on May 22, 2017


  • What strength water balloon launcher do you recommend?
    By xrcise02, on January 17, 2019
View All Comments
2 4

back to top?

Asset 1

Join RYOBI Nation

We're so glad you're here! Let's get started.

Welcome to Ryobi Nation!

Please confirm your email address.

Welcome

Let's build your project feed!

Select some categories to pick the kinds of projects that show up on your home page:


Welcome to Nation

welcome_r2 graphic
Welcome to your RYOBI Nation quick start guide, a fast and easy way to see everything that's waiting for you!
project_feed_r1 graphic
Your feed shows the latest projects from the categories you’ve selected, right on your homepage!
upload_r2 graphic
Are you working on something awesome? Upload your DIY projects today, and share with other members.
contests_r2 graphic
We award monthly and annual prizes for the best projects, worth up to $2500 in RYOBI tools! That’s a lot of hardware, and it could all be yours.
connect_r2 graphic
RYOBI Nation is a positive connection between people who are creating great things.
You can follow fellow members, like their projects, and comment to let them know they’re doing a great job.
notifications_r1 graphic
Come back to RYOBI Nation often to see what is new and to stay in touch.
If you're on a mobile device, don't forget you can add RYOBI Nation to your home screen for quick access to your project feed.

Update Image